[LargeFormat] Re:5x7 Press Graflex Film Holders..
Jim Hemenway
largeformat@f32.net
Sat Jan 10 23:24:11 2004
>>>Sometimes the laquer yellows. It can be removed with laquer thinner
or denatured alcohol and fresh laquer applied. If it isn't yellowed
leave it alone.<<<
Be careful if you use the denatured alcohol as it usually contains some
water. I ruined a camera mirror once by cleaning it with plain ordinary
tap water which washed most of the silver coating away.
Jim - http://www.hemenway.com
> ----- Original Message -----
> From: "tripspud" <tripspud@transbay.net>
> To: <largeformat@f32.net>
> Sent: Friday, January 09, 2004 10:19 AM
> Subject: [LargeFormat] Re:5x7 Press Graflex Film Holders..
>
>
>
>>Hi Richard!
>>
>> I spoke to Alan Brubaker on the phone yesterday, but
>
> it
>
>>appears he is back ordered and I would have to wait for
>
> holders
>
>>to be made. He also makes large holders up to 20x24.
>
> I've put
>
>>him in my address folder.
>>
>> About the 5x7 Press Graflex, this is my third Graflex
>
> reflex camera,
>
>>though the only one presently:
>>
>> The lens is a B&L Tessar 6 1/2 x 8 1/2 and seems
>
> like 10 inch focal length
>
>>and f4.5. The package the camera came in weighed 12 lbs.
>
> and it was mostly
>
>>camera, so it's a big handfull. Fortunately, you don't
>
> have to lift it to your face,
>
>>and it balances rather well at waist level using both
>
> hands. The shutter lever is
>
>>on the left, use the thumb. It's a thrill to see the
>
> image 5x7 without a focusing
>
>>cloth.
>>
>
> The problem with the film holders is that the standard
> holder has a ridge to act as a light trap and to lock the
> holder on the _holder_. The Graflex has the ridge on the
> camera. The two will conspire to lift the end of the holder
> off the back. Even if its light tight it may be tilted.
> Check this.
> AFAIK the reference depth for Graflex holers is the same
> as for Graphic holders of the same size. You can check the
> holder with a depth micrometer and a reference block. The
> block is simply a rigid piece of metal which will extend
> accross the sides of the holder, preferably with a hole in
> it for the depth gauge, although you can use the edge. Just
> measure the thickness of the plate and subtract it from the
> measurement. If the holder is a plate holder a plate of some
> sort must be in it to give a reference surface. The plate is
> usually held against the inside edges of the plate holder by
> a spring.
> The ANSI standard depth for a 5x7 holder is 0.228 inches
> from the outside edge of the holder (its reference surface)
> to the back plate. Most sheet film is 0.007" in thickness,
> this must be subtracted from the above if film is in the
> holder when measured. That distance (0.221) is also the
> depth the emulsion of a glass plate should be from the
> reference surface.
>
> The B&L Series IIb 6-1/2 x 8-1/1 Tessar is 9-7/8ths inches
> FL. The front cell has a threaded back cap, very easy to
> remove, so you can clean the inside of the cell without any
> special tools although a rubber glove may help to grip the
> thing. I have a couple of B&L Tessars of ancient vintage,
> they are actually very good lenses.
> Check the mirror of the camera. These were silvered
> mirrors covered with protective laquer. Sometimes the laquer
> yellows. It can be removed with laquer thinner or denatured
> alcohol and fresh laquer applied. If it isn't yellowed leave
> it alone.
> Once you get the camera going you will have to get a flash
> powder rig so you can be really authentic:-)
>
> ---
> Richard Knoppow
> Los Angeles, CA, USA
> dickburk@ix.netcom.com
>
> My 4x5 Super-D is the same way. Its a double handfull but
> very well balanced with controlls as for yours. No cable
> release, the thing was meant to be hand held. I've taken
> some good children's portraits with it, they don't think I
> am paying any attention to them.
>
>